Docs Menu

Docs HomeDevelop ApplicationsMongoDB Manual

Replica Set Elections

On this page

  • Factors and Conditions that Affect Elections
  • Voting Members
  • Non-Voting Members

Replica sets use elections to determine which set member will become primary. Replica sets can trigger an election in response to a variety of events, such as:

In the following diagram, the primary node was unavailable for longer than the configured timeout and triggers the automatic failover process. One of the remaining secondaries calls for an election to select a new primary and automatically resume normal operations.

Diagram of an election of a new primary. In a three member replica set with two secondaries, the primary becomes unreachable. The loss of a primary triggers an election where one of the secondaries becomes the new primary

The replica set cannot process write operations until the election completes successfully. The replica set can continue to serve read queries if such queries are configured to run on secondaries.

The median time before a cluster elects a new primary should not typically exceed 12 seconds, assuming default replica configuration settings. This includes time required to mark the primary as unavailable and call and complete an election. You can tune this time period by modifying the settings.electionTimeoutMillis replication configuration option. Factors such as network latency may extend the time required for replica set elections to complete, which in turn affects the amount of time your cluster may operate without a primary. These factors are dependent on your particular cluster architecture.

Your application connection logic should include tolerance for automatic failovers and the subsequent elections. MongoDB drivers can detect the loss of the primary and automatically retry certain write operations a single time, providing additional built-in handling of automatic failovers and elections:

Compatible drivers enable retryable writes by default

Replication protocolVersion: 1 reduces replica set failover time and accelerate the detection of multiple simultaneous primaries.

You can use catchUpTimeoutMillis to prioritize between faster failovers and preservation of w:1 writes.

For more information on pv1, see Replica Set Protocol Version.

Replica set members send heartbeats (pings) to each other every two seconds. If a heartbeat does not return within 10 seconds, the other members mark the delinquent member as inaccessible.

After a replica set has a stable primary, the election algorithm will make a "best-effort" attempt to have the secondary with the highest priority available call an election. Member priority affects both the timing and the outcome of elections; secondaries with higher priority call elections relatively sooner than secondaries with lower priority, and are also more likely to win. However, a lower priority instance can be elected as primary for brief periods, even if a higher priority secondary is available. Replica set members continue to call elections until the highest priority member available becomes primary.

Members with a priority value of 0 cannot become primary and do not seek election. For details, see Priority 0 Replica Set Members.

Starting in version 4.4, MongoDB provides mirrored reads to pre-warm electable secondary members' cache with the most recently accessed data. With mirrored reads, the primary can mirror a subset of operations that it receives and send them to a subset of electable secondaries. Pre-warming the cache of a secondary can help restore performance more quickly after an election.

For details, see Mirrored Reads.

With a distributed replica set, the loss of a data center may affect the ability of the remaining members in other data center or data centers to elect a primary.

If possible, distribute the replica set members across data centers to maximize the likelihood that even with a loss of a data center, one of the remaining replica set members can become the new primary.

Tip

See also:

A network partition may segregate a primary into a partition with a minority of nodes. When the primary detects that it can only see a minority of nodes in the replica set, the primary steps down as primary and becomes a secondary. Independently, a member in the partition that can communicate with a majority of the nodes (including itself) holds an election to become the new primary.

The replica set member configuration setting members[n].votes and member state determine whether a member votes in an election.

Although non-voting members do not vote in elections, these members hold copies of the replica set's data and can accept read operations from client applications.

Because a replica set can have up to 50 members, but only 7 voting members, non-voting members allow a replica set to have more than seven members.

Non-voting (i.e. votes is 0) members must have priority of 0.

For instance, the following nine-member replica set has seven voting members and two non-voting members.

Diagram of a 9 member replica set with the maximum of 7 voting members.

A non-voting member has both votes and priority equal to 0:

{
"_id" : <num>,
"host" : <hostname:port>,
"arbiterOnly" : false,
"buildIndexes" : true,
"hidden" : false,
"priority" : 0,
"tags" : {
},
"secondaryDelaySecs" : NumberLong(0),
"votes" : 0
}

Important

Do not alter the number of votes to control which members will become primary. Instead, modify the members[n].priority option. Only alter the number of votes in exceptional cases. For example, to permit more than seven members.

To configure a non-voting member, see Configure Non-Voting Replica Set Member.

←  Replica Set High AvailabilityRollbacks During Replica Set Failover →